How To Repair A Crack In The Foundation In The Garage

Exterior of hairline cracks, larger stress cracks occur when a house settles or the basis beneath information technology shifts. These types of cracks don't usually pose a threat to the structural integrity of a house, but they do allow for a potential opening for groundwater, insects and radon gas.

Nosotros'll show you a simple and effective way to patch cracks with the all-time physical crack filler.

Fix Concrete Cracks in 8 Steps

Step i: Repair a Foundation Cleft With an Epoxy Sealer

Photo Geoffrey Gross

We repaired a foundation wall, which had an 8-ft.-long crack that leaked water into the basement during periods of heavy rainfall. To permanently patch the crack nosotros used an epoxy-injection system from Polygem, called the Liquid Physical Repair Kit (about $lx).

Each kit contains a two-role epoxy crack sealer, two x-oz. tubes of Liquid Concrete Repair (LCR), a viscous epoxy that comes in a caulk-type cartridge, and seven plastic injection ports that evangelize the LCR deep into the crack. There's enough material in each kit to repair a 1/16-in.-broad x 8-in.-deep ten viii-ft.-long crack.

Before y'all start, check to make certain the crack is dry. If the crack is slightly damp, dry out it with a blow-dryer, then wait xv minutes. If it remains dry, go on with the repair. All the same, if the dampness returns, water is notwithstanding seeping into the crack and you'll accept to wait for it to dry out on its own.

First, scrub the crack clean of whatsoever loose concrete, pigment or old crack filler using a wire castor. Remove all dust and debris with a shop vacuum.

Footstep 2: Block Out the Injection Ports

Photograph Geoffrey Gross

Tap 3-in. (10d) finishing nails partway into the crevice, spaced 12 in. apart. You lot'll utilise them to marshal the injection ports with the fissure.

Step 3: Mix the Epoxy Sealer

Photo Geoffrey Gross

Open up upward the two containers of epoxy crack sealer and scoop out equal amounts of Part A and Role B; apply two separate sticks to avoid contamination. Mix the two parts on a flake board using a clean putty knife; blend until you lot achieve a uniform gray color.

Step 4: Attach the Injection Port

Photo Geoffrey Gross

Spread some sealer onto the base of one of the plastic injection ports, being careful not to plug upwards its pigsty. Slide the port over one of the nails sticking out of the crack and press information technology to the wall. Install the remaining ports in a like manner.

Step 5: Spread Sealer Along the Crevice

Photo Geoffrey Gross

Side by side, mix up a slightly larger batch of epoxy sealer and apply it to the entire crack using a i ½-in.-wide putty knife or margin trowel. Spread the sealer about 1/eight in. thick and ane in. on either side of the fissure. Also, embrace the entire flange of each injection port with crack sealer, leaving only the extended neck portion showing. Polish out the sealer and plumage its edges with a paintbrush dipped in mineral spirits.

Step vi: Inject the Epoxy into the Crevice

Photograph Geoffrey Gross

If the other side of the wall is accessible, run into if the crack goes clean through. If it does, seal it upward with crevice sealer, too. Let the sealer to cure for six to x hours before injecting the epoxy. Thoroughly mix the LCR epoxy using the plunger rod that comes with the kit. Place the LCR cartridge into a caulk gun. Starting at the lowest injection port, dispense the epoxy into the crack. Continue squeezing the trigger until epoxy begins to ooze out of the port straight above.

Step 7: Seal Upwardly the Injection Ports

Photo Geoffrey Gross

Remove the gun and plug upward the port you merely filled. Now insert the cartridge tip into the port that's oozing and clasp the trigger to dispense the epoxy. Repeat this process for the remaining ports; plug up each ane earlier moving on to the next.

Stride eight: Cut Away the Injection Ports

Photo Geoffrey Gross

Allow the LCR to cure for five days, then cut off the necks of the ports with a hacksaw. If desired, you can patch the severed ports with a little crack sealer.

Resource:

Polygem
Box 609
Dept. TH700
Due west. Chicago, IL 60186
Polygem
630/231-5600

Source: https://www.thisoldhouse.com/masonry/21016504/fixing-cracks-in-concrete

Posted by: baldwindides1962.blogspot.com

Share this post